求助：出现这样的警告及错误如何调整设置？
<P>各位老师朋友，我的模型的材料是一种塑料，所以我选择是VISCO106，<BR>我想问 1.KINH input. 啥意思？<BR> 2.弹性摸量和泊松比，应力应变曲线我是按文献里给的数据输入的，材料属性选了nonlinear/inelastic/rate independent/kinematic hardening plasticity/mises plasticity/mutilinear下的应力应变。出现下列问题，那位大虾帮我分析以下，谢谢！！！<BR><BR>*** WARNING *** CP = 39.922 TIME= 15:23:27<BR> Both solid model and finite element model boundary conditions have been <BR> applied to this model.As solid loads are transferred to the nodes or<BR> elements, they can overwrite directly applied loads. <BR> <BR>*** ERROR *** CP = 56.609 TIME= 15:35:42<BR> Element 1, which uses viscoplastic element type 106 and material 1, may <BR> not use TB,KINH input. <BR><BR>*** ERROR *** CP = 56.812 TIME= 15:36:12<BR> Isotropic material 1 has a value of Poisson's ratio of 0.5 which causes <BR> a divide by zero.Consider using either a hyperelastic material or <BR> reducing Poisson's ratio to 0.4999. <BR> </P><P> *** ERROR *** CP = 56.906 TIME= 15:36:32<BR> For material 1 at temperature 0, the initial slope of the stress-strain <BR> curve based on the TB,KINH table ( 400 ) is less than EX ( 532700000 <BR> ). <BR></P>
回复：（weiyuanjie）求助：出现这样的警告及错误如何...
The bilinear kinematic hardening model (BKIN) usually cannot represent large-strain effects well because of the constant tangent modulus. The true stress-strain slope of most metals usually changes as the strains increase, but the bilinear model fails to account for this due to its simple <BR>representation. This means that the yield surface can translate forever in principal stress space, even allowing for the unrealistic possibility of passing through the origin. <BR>There are two multilinear kinematic hardening models available in ANSYS, namely MKIN and KINH. Both models use the sublayer model, which can be thought of as a weighted response of multiple elasto-perfectly-plastic ‘layers.’ A simplified view of this is that, as a layer ‘yields,’ it becomes perfectly plastic, so it provides no stiffness response; this allows for the modeling of a piecewise linear curve. The author recommends using KINH over MKIN due to the following reasons: <BR>• KINH allows up to 20 points per stress-strain curve, whereas MKIN only allows up to 5 points. <BR>• For KINH, input is done via TBPT commands, which is more consistent with other piecewiselinear models such as MISO and MELAS, but MKIN relies on TBDATA input. <BR>• KINH allows up to 40 temperature-dependent curves, whereas MKIN allows only 5 temperature-dependent curves. Furthermore, in the case of temperature-dependent curves,MKIN requires each curve to have the same strain values, whereas KINH does not.KINH is the same as MKIN with TBOPT=2, or use of Rice’s model for temperature-dependency. <BR>As a result, KINH behaves the same as MKIN (TBOPT=2), so, due to the reasons mentioned above, the user should consider using KINH.回复：（weiyuanjie）求助：出现这样的警告及错误如何...
VISCO106好像不能用KINH，试试MKIN <P>谢谢，院长</P>
页:
[1]