xianzhang 发表于 2009-3-11 16:22

请教剖分问题

有偿请教剖分问题本人的课题是研究电抗器损耗。其结构如下图：绕组部份由十五层并联而成，每层绕组厚度为3mm.层与层的间隙为0.5mm。绕组上下是铝质结构件。最后给空气建模，建成半径为1m的大球。由于尺寸相差太大，不好剖分。请教如何剖分。

[ 本帖最后由 xuruikl 于 2009-3-14 10:47 编辑 ]

xianzhang 发表于 2009-3-11 16:24

建模命令如下：
/prep7
et,1,solid97
et,2,solid97,1

mp,murx,1,1
mp,murx,2,1            !!!!!!!铜线圈的属性
mp,rsvx,2,3E-8
mp,murx,3,1             !!!!!!!铝板的属性
mp,rsvx,3,4e-8
EMUNIT,MKS

!!!!!!绕组三维建模
n=170
s=0.003*0.5
cylind,0.2,0.203,-0.25,0.25
*repeat,5,0.0035,0.0035,0.001,-0.001

cylind,0.224,0.227,-0.242,0.242
*repeat,5,0.0035,0.0035,0.001,-0.001

cylind,0.248,0.251,-0.24,0.24
*repeat,5,0.0035,0.0035,0.001,-0.001

!!!!!!!!!星形架三维建模

wpoffs,0,0,0.275
cylind,0.02,0.03,-0.02,0.02,0,360
wprota,15
block,0.025,0.28,-0.005,0.005,-0.02,0.02

vsel,s,volu,,16,17
vovlap,16,17
numcmp,volu



wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,18,19
vovlap,18,19
numcmp,volu




wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,20,21
vovlap,20,21
numcmp,volu


wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,22,23
vovlap,22,23
numcmp,volu

wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,24,25
vovlap,24,25
numcmp,volu

wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,26,27
vovlap,26,27
numcmp,volu


wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,28,29
vovlap,28,29
numcmp,volu


wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,30,31
vovlap,30,31
numcmp,volu

wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,32,33
vovlap,32,33
numcmp,volu

wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,34,35
vovlap,34,35
numcmp,volu

wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,36,37
vovlap,36,37
numcmp,volu

wprota,30
block,0.025,0.28,-0.005,0.005,-0.02,0.02
vsel,s,volu,,38,39
vovlap,38,39
numcmp,volu

vsel,all
vdele,16,40,2,1
vplot,all
cylind,0.02,0.03,-0.02,0.02,0,360

numcmp,volu
vsel,s,volu,,16,28
vglue,all
numcmp,volu

vsel,s,volu,,16,28
vsymm,z,all
vsel,s,volu,,29,41
vglue,all
numcmp,volu
allsel,all
vplot,all

!!!!!!!!!!!!!!!!!!空气建模
wprota,15
wpoffs,0,0,-0.275
vsel,all
vplot,all
sphere,0,1
vsel,all
vovlap,all
numcmp,volu

16443 发表于 2009-3-11 17:12

没有明白你说的意思。

xianzhang 发表于 2009-3-11 20:12

我的意思就是：按上面的命令建完的模型怎么剖分

16443 发表于 2009-3-12 08:29

你想要剖分成怎样的 ？

venture 发表于 2009-3-12 08:31

最大尺寸和最小尺寸相差2000倍，如果不对模型进行简化处理，就是勉强给你画出来，计算精度和计算时间都无法保证。

xianzhang 发表于 2009-3-12 09:36

最大尺寸和最小尺寸相差是相差很大.但是我觉得模型简化后不能很好反应真实情况.我导师又要我做一个完整模型的.所以现在愁啊

xianzhang 发表于 2009-3-12 09:44

TO:16443
   我只要剖分后能算就行
页: [1]
查看完整版本: 请教剖分问题