请版主和各位高手们帮我看一下加载时出现的问题
命令流：/units,si
/prep7
et,1,plane82,,,2
mp,dens,1,2700
mp,ex,1,70e9
mp,nuxy,1,0.34
RECTNG,-5,5,0,10,
LESIZE,1, , ,120, , , , ,1
LESIZE,2, , ,120, , , , ,1
LESIZE,3, , ,120, , , , ,1
LESIZE,4, , ,120, , , , ,1
amesh,1
finish
/solu
antype,trans
nsel,s,loc,y,0
dsym,symm,y
allsel
nsel,s,node,,2
finish
! 下面进行加载荷
当输入命令*SET,%_FNCNAME%(0,0,1), 0.0, -999 时就出现如下错误
http://www.simwe.com/forum/attachments/2005/10/02/15338962.jpg
请帮我看一下是什莫问题
谢谢！！
[ 本帖最后由 xinyuxf 于 2007-7-22 16:04 编辑 ] 要先定义一个三维表数组 *SET,_FNCNAME,'TEMP1'
*DIM,%_FNCNAME%,TABLE,6,13,1
*SET,%_FNCNAME%(0,0,1), 0.0, -999 这个好像前面有人做过
是不是用到下面的命令
*SET,_FNCNAME,'TEMP1'
*DIM,%_FNCNAME%,TABLE,6,13,1
! Begin of equation: exp(-1*({X}^2+{{Y}}^2))
*SET,%_FNCNAME%(0,0,1), 0.0, -999
*SET,%_FNCNAME%(2,0,1), 0.0
*SET,%_FNCNAME%(3,0,1), 0.0
*SET,%_FNCNAME%(4,0,1), 0.0
*SET,%_FNCNAME%(5,0,1), 0.0
*SET,%_FNCNAME%(6,0,1), 0.0
*SET,%_FNCNAME%(0,1,1), 1.0, -1, 0, 0, 0, 0, 0
*SET,%_FNCNAME%(0,2,1), 0.0, -2, 0, 1, 0, 0, -1
*SET,%_FNCNAME%(0,3,1), 0.0, -3, 0, 1, -1, 2, -2
*SET,%_FNCNAME%(0,4,1), 0.0, -1, 0, 1, 0, 0, -3
*SET,%_FNCNAME%(0,5,1), 0.0, -2, 0, 1, -3, 3, -1
*SET,%_FNCNAME%(0,6,1), 0.0, -1, 0, 2, 0, 0, 2
*SET,%_FNCNAME%(0,7,1), 0.0, -3, 0, 1, 2, 17, -1
*SET,%_FNCNAME%(0,8,1), 0.0, -1, 0, 2, 0, 0, 3
*SET,%_FNCNAME%(0,9,1), 0.0, -4, 0, 1, 3, 17, -1
*SET,%_FNCNAME%(0,10,1), 0.0, -1, 0, 1, -3, 1, -4
*SET,%_FNCNAME%(0,11,1), 0.0, -3, 0, 1, -2, 3, -1
*SET,%_FNCNAME%(0,12,1), 0.0, -1, 7, 1, -3, 0, 0
*SET,%_FNCNAME%(0,13,1), 0.0, 99, 0, 1, -1, 0, 0
! End of equation: exp(-1*({X}^2+{{Y}}^2))
!ASEL,ALL
DA,ALL,ALL, %TEMP1%
/STATUS,SOLU
页:
[1]